Since then I became interested in embroidery and I purchased my Ellegante 2 in now at an embroidery event at my local store. By Nicholas Myers on April 05 Below you will find a comparison chart showing. Babylock Esante ESE2 information specifications and user forum.
I was so thrilled 5k thinking I was getting a top-of-the-line machine. The Esante allows you to easily arrange your text as well as combine it with your designs on-screen. The power switch is located toward the. Always make sure the power is OFF when the machine is not in use. This appliance has a polarized plug one blade wider than the other.
To reduce the risk of electric shock,. If the plug does not fit fully in the outlet, reverse. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the.
The sewing speed of the machine is determined by the amount of pressure applied to the foot control. When not in use, do not place anything on the foot control, or the machine could start inadvertently and the. Raise the telescopic thread guide to its highest position of 14". Rotate the shaft to the left and right until.
The front cover may be opened simply by placing your. To open the cutting blade cover, place your thumb against the tab, and slide the cover to the right. A slight.
When using threads on cones or king spools place the cone or spool securely over the cone holders furnished on your machine. To avoid bending the thread stand, you may need to place one hand under the stand while positioning the cone.
The cone holders prevent the cone or spool from spinning, enabling the thread to feed evenly fig. Because threads for the serger feed from the top, standard spool threads can snag on the rough edges of many of these spools.
That's why spool caps are furnished with your Imagine to provide a smooth surface that enables the thread to reel off freely. With the spool notch side down, insert a spool cap into the top of the spool. When using standard spool threads on your serger, replace the cone holders with the sponge disks furnished with your machine. These disks hold smaller spools securely and help the thread to reel off properly. With the sponge disk in place, put the capped spool on the spindle fig.
Thread nets may be placed over threads that tend to slip off the bottom of the spool during sewing. Most threads do not require their use, but nets often are necessary with nylon, rayon or silk threads fig. Once it's on the spool, fold the net back on itself, if necessary, to enable the thread to feed smoothly without snagging on the net fig. G One push of the "Jet-Air" threading lever will automatically thread the loopers. It is no longer necessary to use tweezers for threading the thread guides.
E If a thread breaks or runs out, just re-thread it. There is no need to follow any threading sequence. S Locked Position for Threading. Depress the machine lock button firmly.
Rotate the machine handwheel slowly toward you until the but-. Note: The Imagine must be in the locked position when threading the loopers unless otherwise indicat-. With the presser foot up and machine lock button in the locked position fig. A , set the looper threader selector lever to "L" for lower looper threading fig.
Place the thread cone or spool on the far right front spool pin on the thread stand fig. C page Slip the thread into the telescopic antenna thread guide "1" directly above the spool, snap into the thread guide "2" at the top of the machine, through the slot on the front of the machine.
Pull 18 inches 45cm of thread through guide "3". Insert the end of the thread into the threading port "L" about 1 inch 2. Use tweezers if necessary, to insert the thread end more easily.
Depress the looper threading lever fig. D page If the thread does not go through the lower looper eye with one push, depress the threading lever again until it does. Clip the thread 4 inches 10cm from the lower looper eye and leave it hanging loose. Move the lock button release lever to the right. With the presser foot up and machine lock button in the locked position see fig.
A, page 10 , set the looper threader selector lever to "U" for upper looper threading. See fig. B, page Place the thread cone or spool on the second spool pin from the front on the right side of the thread stand fig.
Slip the thread into the telescopic antenna thread guide "A" directly above the spool, snap into the thread guide "B" at the top of the front of the machine, through the slot on the front cover. C, below. Pull 18 inches 45cm of thread through guide "C". Insert the end of the thread into the threading port "U", about 1 inch 2. Use tweezers, if necessary, to insert the thread end more easily. D below. Depress the looper threader lever fig. If the thread does not go through the upper looper eye with one push, depress the looper threader lever again until it does, and leave thread hanging loose.
Move the lock button release lever to the right, to unlock the machine. Turn the handwheel and line up the green marks on the machine and the handwheel. Set the needle threader selector on "R" for right needle fig. B page Note: Be sure to push the needle threader selector all the way to "R".
Place the thread on the second from left spool pin on the thread stand fig. Thread needle thread. Pull a Hold the thread between your left thumb and middle finger fig. With your right index. With the left index finger,. Slip the thread into the.
S threader hook guides in front of the needle. Carefully release the needle threader lever and remove your right index finger, allowing the thread to be pulled through the needle eye. Continue pulling the thread loop manually through the needle eye. Place the thread under the presser foot and to the left. Turn the handwheel to line up the green marks on the machine and handwheel. Set the needle threader selector on "L" for left needle. Place the thread on the far-left spool pin on the thread stand fig.
A page Lower the presser foot and thread the left needle as in steps 4 and 5, under "Right Needle" on page Needle Threader Needle Threader selector. No adjustments are needed when sewing with most fabrics and threads on your Baby Lock Imagine, but certain threads or fabrics may require minor fine-tuning of the looper delivery system to perfect your stitches. Increase or decrease the delivery of the looper threads with the upper and lower looper thread fine-tuning screw.
With a screwdriver found in accessory kit , turn the fine-tuning screw clockwise to tighten the looper threads equally. Turn the screw counter-clockwise to loosen the looper threads equally. You no longer have to manually adjust the tension settings for the type of stitch you are serging. Please check your manual to verify which bobbin style is right for your machine.
In a few short steps you could own the machine of your dreams with convenient monthly payments and promotional financing. Completing the application will tell you how much credit Synchrony will extend to you. You are not charged until you place an order with SewingMachinesPlus. Read More. Call for details. More images coming later. The eM2 is whisper-quiet, produces no fumes or emissions, and provides a smooth ride with impressive acceleration. With the Freightliner Electric Innovation Fleet and Customer Experience Fleet pilot programs, we learn more lessons every day about life on the road behind the wheel of electric trucks.
A few perks that participating drivers have shared:. Energy prices vary by region and also fluctuate on an hourly basis, depending on when the energy grid is experiencing spikes in demand. This means that the cost of energy is typically lower at night, so use cases that allow for overnight truck charging are ideal for maximizing fuel savings.
Even after considering fluctuations in energy price, the cost-per-mile of running trucks on electricity is expected to be significantly lower than running them on diesel fuel. Depending on the region of deployment, grants and incentives may be available to offset the higher initial purchase price of an electric truck, pushing it closer to parity with a comparable diesel truck.
0コメント